极速快乐8

  热门关键词:
BS ISO 16232-3-2007 Road vehicles- Cleanliness of components
  • 该文件为doc格式
  • 文件大小:270.10 KB
  • 下载次数
  • 文件评级
  • 更新时间:2020-03-30
  • 发 布 人Inventororor
  • 文件下载:
  • 立即下载

  • 文件介绍:
  • 该文件为 doc 格式,下载需要 1 积分
  • BS ISO 16232-3-2007 Road vehicles- Cleanliness of componentsNational foreword
    This British Standard was published by BSI. It is the UK implementation of ISO 16232-3:2007.The UK participation in its preparation was entrusted to Technical Committee MCE/22, Engines for road vehicles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.
    Compliance with a British Standard cannot confer immunity from legal obligations.












    This British Standard was Amendments issued since publication
    Amd. No. Date Comments




    published under the authority
    of the Standards Policy and
    Strategy Committee
    on 29 June 2007

    © BSI 2007




    INTERNATIONAL ISO16232-3
    STANDARD
    First edition
    2007-06-01
    Road vehicles — Cleanliness of components of fluid circuits —
    Part 3:
    Method of extraction of contaminants by pressure rinsing



































    Contents Page

    Foreword............................................................................................................................................................ iv
    Introduction....................................................................................................................................................... .v
    1 Scope..................................................................................................................................................... 1
    2 Normative references........................................................................................................................... 1
    3 Terms and definitions........................................................................................................................... 2
    4 Principle................................................................................................................................................. 2
    5 Equipment............................................................................................................................................. 2
    5.1 General................................................................................................................................................... 2
    5.2 Test liquid.............................................................................................................................................. 2
    5.3 Test component container................................................................................................................... 2
    5.4 Pressure rinsing liquid dispenser....................................................................................................... 2
    5.5 Clean-up filter........................................................................................................................................ 2
    5.6 Vacuum suction system....................................................................................................................... 2
    5.7 Collection equipment........................................................................................................................... 2
    5.8 Sampling containers............................................................................................................................. 3
    5.9 Environmental conditions.................................................................................................................... 3
    5.10 Health and safety.................................................................................................................................. 3
    6 Procedure.............................................................................................................................................. 3
    6.1 Handling and storage........................................................................................................................... 3
    6.2 Extraction procedure set-up and validation...................................................................................... 3
    6.3 Blank test............................................................................................................................................... 6
    6.3.1 Sources of blank contamination........................................................................................................ .6
    6.3.2 System blank test................................................................................................................................. 7
    6.3.3 Blank value............................................................................................................................................ 7
    6.4 Component routine test....................................................................................................................... 8
    7 Analysis of the extraction liquid......................................................................................................... 8
    8 Presentation of results......................................................................................................................... 9
    Annex A (informative) Synopsis of the extraction procedure set-up and validation...................... 10
    Annex B (informative) Example of data sheet for the extraction procedure by pressure rinsing........... 11
    Annex C (informative) Synopsis of the routine test procedure................................................................... 14
    Bibliography..................................................................................................................................................... 15










    Foreword
    ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

    International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

    The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

    Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ...
文档留言
验证码: 请在右侧输入验证码 看不清楚,换一个
更多..相关文档
    无相关信息
极速赛车开户 qq分分彩投注 香港开奖结果2019+开奖记录表 山东群英会选号技巧 北京11选5开奖 极速快三计划 河北11选5开奖 德国赛车网址 北京两步彩 德国赛车网址