极速快乐8

  热门关键词:
BS ISO 16232-2-2007 Road vehicles
  • 该文件为doc格式
  • 文件大小:260.37 KB
  • 下载次数
  • 文件评级
  • 更新时间:2020-03-30
  • 发 布 人Inventororor
  • 文件下载:
  • 立即下载

  • 文件介绍:
  • 该文件为 doc 格式,下载需要 1 积分
  • BS ISO 16232-2-2007 Road vehiclesContents Page

    Foreword........................................................................................................................................iv

    Introduction....................................................................................................................................v
    1 Scope.............................................................. .................................................................. 1
    2 Normative references......................................................................................................... 1
    3 Terms and definitions............................................................................................... 2
    4 Principle...................................................................................................................... 2
    5 Equipment................................................................................................................... .2
    5.1 General.................................................................................................................... 2
    5.2 Test liquid......................................................................................................................... 2
    5.3 Test component container........................................................................................... 2
    5.4 Pressure rinsing liquid dispenser............................................................................................ 2
    5.5 Vacuum suction system............................................................................................... 2
    5.6 Collection equipment.......................................................................................................... 2
    5.7 Sampling containers............................................................................................................ 3
    5.8 Environmental conditions............................................................................................. 3
    5.9 Health and safety....................................................................................................... 3
    6 Procedure............................................................................................................................ 3
    6.1 Handling and storage................................................................................................. 3
    6.2 Extraction procedure set-up and validation.................................................................... 3
    6.3 Blank test......................................................................................................................... 6
    6.4 Component routine test........................................................................................................8
    7 Analysis of the extraction liquid.......................................................................................... 9
    8 Presentation of results........................................................................................................ 9

    Annex A (informative) Synopsis of the extraction procedure set-up and validation....................10
    Annex B (informative) Example of data sheet for the extraction procedure by the agitation method.. ............. 11
    Annex C(informative) Synopsis of the routine test procedure........................................... 14
    Bibliography...................................................................................................................................15











    Foreword
    ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

    International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

    The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.

    Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

    ISO 16232-2 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 5, Engine tests.

    ISO 16232 consists of the following parts, under the general title Road vehicles — Cleanliness of components of fluid circuits:
    ⎯Part 1: Vocabulary

    ⎯Part 2: Method of extraction of contaminants by agitation

    ⎯Part 3: Method of extraction of contaminants by pressure rinsing

    ⎯Part 4: Method of extraction of contaminants by ultrasonic techniques

    ⎯Part 5: Method of extraction of contaminants on functional test bench

    ⎯Part 6: Particle mass determination by gravimetric analysis

    ⎯Part 7: Particle sizing and counting by microscopic analysis

    ⎯Part 8: Particle nature determination by microscopic analysis

    ⎯Part 9: Particle sizing and counting by automatic light extinction particle counter
    Introduction

    The presence of particulate contamination in a fluid system is acknowledged to be a major factor governing the life and reliability of that system. The presence of particles residual from the manufacturing and assembly processes will cause a substantial increase in the wear rates of the system during the initial run-up and early life, and may even cause catastrophic failures.

    In order to achieve reliable performance of components and systems, control over the amount of particles introduced during the build phase is necessary, and measurement of particulate contaminants is the basis of control.

    The ISO 16232 series has been drafted to fulfil the requirements of the automotive industry, since the function and performance of modern automotive fluid components and systems are sensitive to the presence of a single or a few critically sized particles. Consequently, ISO 16232 requires the analysis of the total volume of extraction liquid and of all contaminants collected using an approved extraction method.

    The ISO 16232 series has been based on existing ISO International Standards such as those developed by ISO/TC 131/SC6. These International Standards have been extended, modified and new ones have been developed to produce a comprehensive suite of International Standards to measure and report the cleanliness levels of parts and components fitted to automotive fluid circuits.
    ...
文档留言
验证码: 请在右侧输入验证码 看不清楚,换一个
更多..相关文档
    无相关信息
北京快3 澳洲幸运10平台 任我赢机器人 飞速时时彩 极速快乐十分 北京赛车 东京1.5分彩登陆 北京11选5走势图 飞速赛车平台 百万彩票